DXLink HDMI Multimode Duplex Fiber Receiver
Model: DXF-RX-MMD
Part #: FG1010-562
- Only One Cable – Send audio and video, while passing Ethernet signals and power over one twisted pair cable
- Multi-Format Analog Port and HDMI Port – Supports legacy analog signals - RGBHV, Component, S-Video, and Composite, and digital HDMI/HDCP, DisplayPort++ and DVI signals
- Send HDMI signals up to 100 meters – Extend the reach of the HDMI signals far beyond the capabilities of typical HDMI cabling
- Standard Twisted Pair Cable – Save time and effort in installation by leveraging cost effective twisted pair cable, see the Cabling for Success with DXLink white paper for more details
- Power over DXLink Enabled – Designed for use with Enova DGX or DVX systems with DXLink inputs, PS-POE-AT-TC (FG423-84) or PDXL-2 (FG1090-170) to provide remotely located Power over DXLink (requires firmware v1.2.40 or above)
The DXLink HDMI Fiber Receiver features built-in SmartScale® Technology to deliver HDMI with HDCP that is perfectly scaled for each connected display automatically, eliminating the integration challenges that can occur when sources and displays have different optimal resolutions. It accepts audio, video, control and Ethernet over multimode fiber from up to 300 meters. Mount the low-profile DXLink Fiber Receiver behind a display or above a ceiling mounted projector and control it using the built in RS-232 or IR ports. Plus monitor the connected display's settings, and send IR control signals to the Enova DGX Digital Media Switcher with integrated NetLinx® control back to the source device.
COMMON APPLICATIONS
The ideal solution for any destination display or projector designed into an Enova DGX integrated system that requires the distance capabilities and inherent security of fiber – or both; including campus-wide distribution of sources that are shared between classrooms, secure military applications, casinos, arenas and museums. Directly connect LCDs, plasmas and projectors using the HDMI output connection while delivering room audio via the stereo audio output.
- Only One Cable – Send audio and video, while passing Ethernet signals and power over one twisted pair cable
- Multi-Format Analog Port and HDMI Port – Supports legacy analog signals - RGBHV, Component, S-Video, and Composite, and digital HDMI/HDCP, DisplayPort++ and DVI signals
- Send HDMI signals up to 100 meters – Extend the reach of the HDMI signals far beyond the capabilities of typical HDMI cabling
- Standard Twisted Pair Cable – Save time and effort in installation by leveraging cost effective twisted pair cable, see the Cabling for Success with DXLink white paper for more details
- Power over DXLink Enabled – Designed for use with Enova DGX or DVX systems with DXLink inputs, PS-POE-AT-TC (FG423-84) or PDXL-2 (FG1090-170) to provide remotely located Power over DXLink (requires firmware v1.2.40 or above)
- DXLink Direct Connection – When receiving Power over DXLink
- from the PS-POE-AT-TC or PDXL-2, DXLink Wallplates can be connected directly to a DXLink Receiver for a point-to-point solution
- Note:
- Power must be supplied by one of the following DXLink Power sourcing devices:
- Enova DGX 8/16/32/64 Digital Media Switcher (with a DXLink Twisted Pair Input Board installed), Compatible Enova DVX All-In-One Presentation Switcher (3155HD, 3156HD or 2155HD), PS-POE-AT-TC High Power PoE Injector or PDXL-2 Power over DXLink Controller.
- AMX only supports the use of these approved Power over DXLink solutions. Other third party power supplies or non-compatible standard PoE solutions may damage the DXLink equipment
- Fiber Optic Connector Type - LC-LC
- Fiber Optic Signals Supported - Audio
- Fiber Optic Signals Supported - HDMI
- ROHS Compliant - Yes
- Warranty - Yes
- Spec Sheet available - Yes
- Operating Temperature (Maximum): 104 F
- Operating Temperature (Minimum): 32 F
- Certifications: FCC, CE, UL
- Regulatory Compliance: WEEE, HDCP
- AC Voltage (Maximum): 240 Volts
- AC Voltage (Minimum): 100 Volts
- Active Power: 20 Watt
- Depth: 5.25 in
- Height: 1 in
- Width: 8.75 in
- Product Weight: 1.10 lbs
- Shipping Weight: 2.20 lbs
- Operating Distance (Multimode): 984.25 ft
- Maximum Frequency Response (Bandwidth): 20 kHz
- Maximum Frequency Response (Bandwidth): 20000 Hz
- Minimum Frequency Response (Bandwidth): 50 Hz
- Minimum Frequency Response (Bandwidth): 0.05 kHz
- Warranty (Length/Type): 3 Years Limited
- Power:
- Power Connector: 2.1 mm DC Power Jack
- POWER SUPPLY:
- External, Included: Each HDMI RX ships with a desktop power supply with power cord, 2.5 A @ 12 V, Max 13.5 V
- Environmental:
- Temperature (Storage): 22° F to 158° F (-30° C to 70° C)
- Humidity (Operating): 5% to 85% RH (non-condensing)
- Humidity (Storage): 0% to 90% RH (non-condensing)
- Heat Dissipation (On): 69 BTU/hr
- Ethernet:
- Ethernet Connection: (1) RJ-45, TCP/IP Port (ICS LAN 10/100)
- DXLINK FIBER:
- Fiber Connector: LC Duplex conforming to ANSI TIA/EAI 604-10 (FOCIS 10A)
- Fiber Cable Type: OM3 50/125µm
- Fiber Cable Length: 300m (984 ft)
- Transport Layer Throughput: 10.3125 Gbps
- Fiber Transceiver Type: 10G SFP+
- Optical Wavelength: 850 nm
- Optical Budget:
- 6.8 dB (typical) between DXLink Fiber Transceivers
- Optical Modulation Amplitude (OMA): -4.3 dBm (min)
- Optical Modulation Amplitude (OMA) Sensitivity: -11.1 dBm (typ)
- Optical Transceiver Mean: -1 dBm (average power)
- HDMI:
- Output Connector: (1) HDMI Type A Female
- Compatible Formats: HDMI, HDCP , DVI
- Signal Type Support:
- HDMI
- DVI-D (single link with HDMI cable adapter)
- Progressive Resolution Support:
- All progressive resolutions between 480p and 1920 x 1200 @ 60 Hz via automatic SmartScale query of the display's preferred DID Detailed Timing Definition
- Interlaced Resolution Support:
- 480i, 576i, 1080i
- Including but not limited to those resolutions shown in the "Instruction Manual - DXLink Fiber Transmitters and Receivers"
- Interlace video supported into the Transmitter, progressive only supported out of the Receiver unless in non-scaling Bypass
- Output Scaling: SmartScale or Manual Configuration or Bypass
- 3D Format Support:
- Yes, if Scaler on RX is set to Bypass mode
- Frame Packing 1080p 24Hz
- Frame Packing 720p 50/60Hz
- Frame Packing 1080i 50/60Hz
- Top-Bottom 1080p 24Hz
- Top-Bottom 720p 50/60Hz
- Side-by-Side Half 1080i 50/60Hz
- Deep Color Support:
- 24-bit, 30-bit
- 30-bit supported when the HDMI Output Board scaler or DXLink RX scaler is in Bypass mode using CEA-861 formats and resolution is 1080p60 or less
- Color Space Support:
- RGB 4:4:4
- YCbCr 4:4:4 and 4:2:2
- Input signal support for YCbCr 4:4:4 and 4:2:2, output color-space is converted to RGB 4:4:4
- HDCP Support:
- Yes
- Supports AMX HDCP InstaGate Pro Technology When used with an Enova DGX Digital Media Switcher the key support is up to 16 sinks per output, independent of source device
- CEC Support: None
- Propagation Delay (Typical): 26 ms when scaling, 5.2 us when in Bypass mode
- CDR (Re-Clocking): Yes
- Output Voltage (Nominal): 1.0 Vpp Differential
- Output Rise Time / Fall Time: 425 ps typ (20% - 80%)
- Video Data Rate (Max):
- 4.95 Gbps / 5.568 Gbps
- 5.568 Gbps supported when the HDMI Output Board scaler or DXLink RX scaler is in Bypass mode using CEA-861 formats and resolution is 1080p60 or less
- 4.95 Gbps / 5.568 Gbps
- Video Pixel Clock (Max):
- 165 MHz / 185.625 MHz
- 185.625 MHz supported when the HDMI Output Board scaler or DXLink RX scaler is in Bypass mode using CEA-861 formats and resolution is 1080p60 or less
- 165 MHz / 185.625 MHz
- Audio Format Support:
- Dolby TrueHD, Dolby Digital, DTS-HD Master Audio, DTS, 2 CH through 8 CH L-PCM
- Dolby Digital and DTS support up to 48kHz, 5.1 channels
- Audio Resolution: 16 bit to 24 bit
- Audio Sample Rate: 32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192kHz
- Local Audio Support: Extraction
- ANALOG AUDIO:
- Output Connections: 3.5mm Mini-Stereo Jack
- Output Signal Types: Stereo Analog
- Output Level (Max): 0 dBU, unbalanced, >= 2 kOhm load
- Output Frequency Response: < +0 dB to -0.5 dB, 50 Hz to 20 kHz
- Audio THD+N: <0.04%, 1 kHz, -10dBu to +2 dBu
- Audio S/N Ratio: >93 dB, 20 Hz to 20 kHz Vin=+2dBu
- Digital to Analog Reference Level: 0 dBfs = +0 dBu
- Audio Synchronization: Video formats @ 60Hz frame rate: video formats @ 60Hz frame rate: In scaling mode audio leads video by 12ms typ (4ms to 20ms). In Bypass mode, audio lags video by 14ms
- USB (HID) KEYBOARD & MOUSE:
- USB (HID):
- (1) USB Mini A/B Connector ("DEVICE")
- Connect a keyboard & mouse and send commands to a PC connected to a DXLink Twisted Pair or Fiber TX
- For a list of HID devices which have been tested and found to be working well with the latest firmware please view the document
- USB (HID):
- Controls:
- ID Pushbutton
- Toggle between DHCP and static IP addressing
- Places system in NetLinx Device ID assignment mode
- Reset the factory default settings
- Restore the factory firmware image
- Advanced Configuration Interface: (1) USB Mini-B Connector ("PROGRAM"):
- Serial:
- (1) 3.5mm Pluggable Phoenix Terminal Block
- Bidirectional RS-232 Standard NetLinx Baudrate 1200-115k
- Parity support Odd/Even/None
- IR RX: (1) 3.5mm Mini-Stereo Jack Port for IR03 Receiver (Optional)
- IR TX: (1) 3.5mm Pluggable Phoenix Terminal Block Port for IR01 Emitter (Optional)
- ID Pushbutton
- Indicators:
- Power Indicator: (1) LED that lights:
- Green during normal operation state
- Red when power is applied and boot sequence is started
- Yellow when system initialization is in process
- Digital Video Indicator: (1) Green LED indicates the presence of video signals through the module
- Audio Indicator: (1) Green LED indicates the presence of digital audio signals through the module
- Scaling Button and LEDs: (1) Pushbutton and (3) Green LEDs; use Scaling button to select one of the three options: Bypass, Auto (SmartScale), or Manual. The factory default is Auto (SmartScale). If the RX power cycles, it defaults to the last persisted mode (achieved by pressing scaling button and holding it until the desired scaling mode LED flashes)
- IR TX Indicator: (1) Red LED lights during the transmission of IR data via the rear IR port
- IR RX Indicator: (1) Yellow LED lights during the receipt of IR data via the rear IR port
- RS-232 TX Indicator: (1) Red LED shows serial transmit (TX) data activity
- RS-232 RX Indicator: (1) Yellow LED shows serial receive (RX) data activity
- LINK/ACT: (1) Green LED lights when the Ethernet cable is connected and an active link is established. This LED also blinks when receiving Ethernet data packets
- Status: (1) Green LED lights when the Controller is programmed and communicating properly
- CEC Indicator: Not currently supported
- USB Indicator: (1) Yellow LED lights when either a Keyboard or mouse is connected directly to the RX, or either and/or both are connected to a USB Hub connected to the RX ID Pushbutton: Places system in NetLinx Device ID assignment mode
- Power Indicator: (1) LED that lights:
- Front Connectors:
-
Advanced Configuration Interface: (1) USB Mini-B Connector ("PROGRAM")
- Back Connectors:
- Local Power: 2.1 mm DC Power Jack
- DXLink Fiber Input: LC Duplex conforming to ANSI TIA/EAI 604-10 (FOCIS 10A)
- ICS LAN/Ethernet Port: (1) RJ-45 Connector, TCP/IP Port (ICS LAN 10/100) Serial:
- (1) 3.5mm Pluggable Phoenix Terminal Block
- Bidirectional RS-232 Standard NetLinx Baudrate 1200-115k
- Parity support Odd/Even/None IR RX
- IR RX: (1) 3.5mm Mini-Stereo Jack Port for IR03 Receiver (Optional)
- IR TX: (1) 3.5mm Pluggable Phoenix Terminal Block Port for IR01 Emitter (Optional)
- USB (HID) Keyboard & Mouse:
- (1) USB Mini A/B Connector
- Connect a keyboard & mouse and send commands to a PC connected to a DXLink Twisted Pair or Fiber
- HDMI Output: HDMI Type A Female
- Analog Stereo Output: 3.5mm Mini-Stereo Jack
- General:
- MTBF: 124,232 hours
- Noise Level: 0 dBA @ 1m (typ), 45.3 dBA @ 1m (max)
- Airflow: Convection (openings on top of case, typ), forced air (out of front plate, when fan is active)
- Mounting Options:
- Compatible V Style mounting options:
- AVB-VSTYLE-RMK-FILL-1U, V Style Module Rack Mounting Tray /w Fill Plates, 5 1/4" Depth (FG1010-721)
- AVB-VSTYLE-RMK-1U, V Style Module Rack Mounting Tray, 5 1/4" Depth (FG1010-720)
- AVB-VSTYLE-SURFACE-MNT, V Style Single Module Surface Mount Brackets (FG1010-722)
- AVB-VSTYLE-POLE-MNT, V Style Single Module Pole Mounting Kit (FG1010-723)
- Regulatory Compliance:
- CE EN 55022 Class A
- CE EN 55024
- CE EN 60950-1
- IEC 60950-1
- ICES-003 Class A
- Safety Certification:
- Class 1 Eye safe per requirements of IEC 60825-1 / CDRH
- Included Accessories:
- Ships with a desktop power supply with power cord
- Optional Accessories:
- AVB-VSTYLE-RMK-FILL-1U, V Style Module Rack Mounting Tray /w Fill Plates, 5 1/4" Depth (FG1010-721)
- AVB-VSTYLE-RMK-1U, V Style Module Rack Mounting Tray, 5 1/4" Depth (FG1010-720)
- AVB-VSTYLE-SURFACE-MNT, V Style Single Module Surface Mount Brackets (FG1010-722)
- AVB-VSTYLE-POLE-MNT, V Style Single Module Pole Mounting Kit (FG1010-723)
- CC-NIRC, NetLinx IR Emitter Cable (FG10-000-11)
- IR03, External IR Receiver Module (FG-IR03)
- CC-MINIUSB, Mini USB to PC Cable Adapter (FG5967-20)
- Compatible AMX Products:
- Enova DGX 8/16/32/64 Digital Media Switchers with DGX-O-DXF-MMD, Enova DGX DXLink Mutimode Fiber Output Board, Duplex (FG1058-632) installed
Suggested Products
Lowrance Sound Company, Inc.
2132 Nailing Drive
Union City, TN 38261
USA
(901) 885-4504
www.lowrancesoundcompany.com